1 a aging 老化
2 b battery charger 充電器
3 black-fleck 黑斑
4 c cap 蓋板
5 capacity density 能量密度
6 capacity grading 分容
7 cathode tab welding 極耳超焊
8 cell 電芯
9 charge(capacity) retention 荷電（容量）保持
10 checking code 檢碼
11 concave spot 凹點
12 constant current charge 恒流充電
13 constant current discharge 恒流放電
14 constant voltage charge 恒壓充電
15 corrective measures 糾正措施
16 crack 裂紋
17 cut-off voltage 終止電壓
18 cycle life 循環壽命
19 d dark trace 暗痕
20 degrade 降級
21 dent 凹痕
22 discharge depth 放電深度
23 distortion 變形
24 drape 打折
25 e electrical and mechanicalservices department 機電部
26 electrolyte 電解，電解液
27 empaistic 壓紋
28 end-off voltage 放電截止電壓
29 environmentally friendly 對環境友好
30 equipment first inspection 設備首檢
31 erode 腐蝕
32 explosion-proof line 防爆線
33 f first inspection 首檢
34 formation 化成
35 fracture 斷裂
36 i inspection 檢驗
37 insulate 絕緣
38 internal resistance 內阻
39 j jellyroll 卷芯
40 joint 接縫，結合點
41 l laser deflecting 偏光
42 laser reticle 激光刻線
43 laser welding-flatwise weld 激光焊接-平焊
laser welding-standing weld 激光焊接-立焊
44 leakage 漏液
45 leak-checking 測漏
46 leaving out of welding 漏焊
47 limited charge voltage 充電限制電壓
48 local action 自放電
49 m margin turnly 翹邊
50 measuring the dimension of cells 電芯卡尺寸
51 meet requirement 達到要求
52 memory effects 記憶效應
53 n nick 劃痕
54 nominal voltage 標稱電壓
55 notice-board confirmation 看板確認
56 nugget 硬塊
57 o obverse 正面
58 open circuit voltage 開路電壓
59 over charge 過充
60 over discharge 過放
61 over the thickness 超厚
62 p particle 顆粒
63 pe membrane pe膜
64 pit 坑點
65 placing cells into the box 電芯裝盒
66 point inspection 點檢
67 preventive measures 預防措施
68 pricking the tapes 扎孔
69 process inspection 制程檢驗
70 put the battery piled up 將電芯疊放在一起
71 q qualified products 合格品
72 quality assurance 質量保證
73 quality control 質量控制
74 quality improvement 質量改進
75 quality match 品質配對
76 quality planning 質量策劃
77 r rated capacity 額定容量
78 recharge 再充電
79 refitting the can of cell 電芯殼口整形
80 requirment 要求
81 reverse 背面，反面
82 rework 返工
83 ringing cells into pyrocondensation films 套熱縮膜
84 s safety vent 安全閥
85 sand aperture 砂眼
86 scar 疤痕
87 secondary battery 二次電池
88 select appearance 選外觀
sharp-set 批鋒
89 short circuit checking 測短路
90 smudginess 污物
91 spot welding by laser 激光點焊
92 spot welding place 點焊位置
93 spraying the code 噴碼
94 spur 毛刺
95 sticking the pvc cover boards 貼面墊
96 storing 陳化
97 storing with high voltage 高壓儲存
98 t tabs deflection 極耳歪斜
99 tabs excursion 極耳錯位
100 technics requiment 工藝要求
101 u ultrasonic welding 超聲波焊接
102 ultrasonic welding strength 超焊強度 |<< << < >>