I-beam axle 前軸工字梁
Identification number （機器）識別號
Idle adjusting nut 怠速調節螺母
Idle adjusting screw 怠速調節螺釘
Idle compensator 空轉補償器
Idle gear 中間齒輪，惰輪
Idle limiter 怠速限制器
Idle mixture control body 怠速混合氣控制體
Idle mixture richness 怠速混合氣濃度
Idle running 怠速運轉
Idling speed 怠速轉速
Ignite 點火
Ignition 點火
Ignition advancer 提前點火裝置
Ignition analyzer 點火分析器
Ignition by heat of compressio 壓燃
Ignition cam 點火分電器凸輪
Ignition circuit 點火線路
Ignition contact breaker 點火斷電器
Ignition control hand lever 點火提前控制手柄
Ignition cut-out button 點火斷電鈕
Ignition device 點火裝置
Ignition distributor 分電器
Ignition hole 點火孔
Ignition impulse coupling 沖擊點火聯軸節
Ignition lag 點火延遲
Ignition noises 點火噪聲
Ignition order 點火順序
Ignition paper 點火紙
Ignition plug 火花塞
Ignition plug with double spark 雙極火花塞
Ignition point 燃點，著火溫度
Ignition screening 點火屏蔽
Ignition spark 點火火花
Ignition system 點火裝置，點火系統
Ignition temperature 點火溫度
Ignition timing 點火定時
Ignition timing control system 點火時刻控制系統
Ignition warning light 點火告警燈
Ignition wrench 火花塞扳手
I-head combustion chamber I型燃室
I-head cylinder I型缸蓋式氣缸
Indicated lateral acceleration 指示橫向加速度
Indicating instrument 指示儀表
Indicating plug ga(u)ge 指示式塞規
Indicator 指示器
Indicator lamp 指示燈
Individual drive of machine tools 機床獨立驅動
Individual ignition cut out switch 單獨點火斷電器開關
Induced current 感應電流
Induced electric motive force 感應電動勢
Induction 吸入，進氣；感應
Induction current 感應電流
Induction manifold 進氣歧管
Induction melting furnace 感應熔化爐
Induction period 吸氣時間,進氣時間
Induction soldering 感應焊接
Inductive heat treatment 感應熱處理
Inductive ignition system 電感點火系統
Inductor generator 感應發電機
Inductor magneto 感應磁電機
Inductor motor 感應式電動機
Inertia braking system 慣性制動系
Inertia charge 慣性增壓
Inertia diagram 慣性力圖
Inertia force 慣性力
Inertia principal axes system （簧上）慣性主軸坐標系
Inertia proportioning valve 慣性比例閥
Inertia starter 慣性起動器
Injection 噴射，注入
Injection advance 噴射提前
Injection carburetor 噴射式化油器
Injection mould 注塑模具
Injection moulded plastic part 注塑零件
Injection nozzle 噴油嘴
Injection pressure 噴射壓力
Injection pump 噴射泵
Injection timing device 噴射正時裝置
Injector 噴嘴
Injector comparator 噴油器對比器
Inlet 進氣
Inlet air pipe 進氣管
Inlet connector 進油管接頭
Inlet filter 進油口過濾器
Inlet manifold 進氣歧管
Inlet mainford heat regulator 進氣歧管溫度調節器
Inlet manifold port 進氣歧管口
Inlet nipple 進油管接頭
Inlet of cold air 冷空氣進口
Inlet opening 進氣孔
Inlet pipe 進氣管
Inlet port 發動機進氣口
Inlet silencer 進氣管消聲閥
Inlet temperature 進氣溫度
Inside race 軸承內圈
|<< << < >>